Search Results

This paper presents velocity and pressure measurements obtained around an isolated wheel in a rotating and stationary configuration. The flow field was investigated using LDA and a total pressure probe in the model scale wind tunnel at IVK/FKFS. Drag and lift were determined for both configurations as well as for the wheel support only. These results were used as a reference for comparing numerical results obtained from two different CFD codes used in the automotive industry, namely STAR-CD™ and PowerFLOW™. The comparison gives a good overall agreement between the experimental and the simulated data. Both CFD codes show good correlation of the integral forces. The influence of the wheel rotation on drag and lift coefficients is predicted well. All mean flow structures which can be found in the planes measured with LDA can be recognized in the numerical results of both codes. Only small local differences remain, which can be attributed to the different CFD codes.

In automotive wind tunnels with modern road simulation installations boundary layer pre-suction is a widely-used technique for boundary layer control. The consequence of boundary layer pre-suction is an additional pressure gradient in front of the model. In order to investigate the effects of the additional pressure gradient on drag, experiments were conducted with two different models (scale 1:5) in the IVK Model Wind Tunnel. In these experiments the suction velocity of the boundary layer pre-suction served as a parameter to change the static pressure gradient along the test section and was for this purpose adjusted higher and lower than the standard suction velocity. It is shown that the total drag increment due to boundary layer pre-suction consists of at least two parts: the ground simulation increment and the static pressure gradient increment. The ground simulation increment is due to a decrease in the boundary layer thickness and the resulting modified flow beneath the model.

This paper introduces a driving-torque measurement method for the determination of vehicle road load and its components. To increase the accuracy, the torque measurements are combined with rolling resistance measurements performed with a specially developed trailer. This method is a strictly experimental approach and does not use any mathematical models. The experimental techniques are described as well as the proceedings to compare test stand and road measurements. The results that are shown prove that this method is suitable for the investigation of single road load components. Furthermore, the comparison of different rolling resistance measurement devices shows the potential of the measurement trailer and the necessity to perform rolling resistance measurements on real road surfaces and not solely on test stands.

In 2001 the FKFS (Research Institute of Automotive Engineering and Vehicle Engines, Stuttgart) took into operation state-of-the-art 5-belt systems for road simulation in the 22.45m2-IVK automotive wind tunnel and in the 1.65m2-IVK model wind tunnel. In these systems, a narrow belt running between the vehicles' wheels is fitted with 4 balance-mounted wheel rotation drives and a vehicle restraint system. The FKFS opted for MTS steel belt technology due to its small size, low power requirements and excellent tracking stability. Due to air bearings below the belt, the flat-belt wheel rotation units in the full-scale wind tunnel permit aerodynamic force measurements at full wheel load (8 kN) up to 70 m/s. In combination with the hydrostatic suspension of the units, integrated longitudinal force transducers permit realistic measurements of the wheels' rolling resistance. In the model wind tunnel FKFS wheel rotation units with Poly-V belts are used with small wheel loads up to 80 m/s.

Investigating the crosswind behavior of passenger cars is one main research subject at the Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS), an institute of the University of Stuttgart. Faced with the vehicle dynamics during stochastic crosswind, this paper is concerned with the evaluation of the crosswind behavior as experienced by the driver. Most of the evaluation criteria of crosswind are currently based on the vehicle reactions only and exclude the driver's actions. A comparison of the crosswind behavior of two vehicles at the FKFS showed a non-uniform - in some cases even contrary - evaluation when applying these criteria. This paper introduces a new approach to considering the vehicle's crosswind behavior which includes the driver's reactions. The fundamental issue of this new approach is to derive the driver's evaluation from their steering inputs when compensating for the crosswind excitation. In other words: The driver is used as a sensor.

Within the scope of a current research project at the Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS), the potential for an estimation of vehicle side slip angle and yaw rate arising from online measurement of tire forces is evaluated. Investigations focus on how the vehicle state can be determined, if in addition to wheel speeds and steering angle the tire forces currently acting on the vehicle are known. Different estimation procedures based on inverse tire models, direct integration of vehicle accelerations and closed-loop-observer are discussed. The performance is tested with data from vehicle dynamics simulation.

The number of electronic control units (ECU) in modern automobiles has steadily increased lately. Joining them in a vehicle network causes complex bus structures, in which ECU's of different suppliers have to cooperate. In order to keep the development effort as small as possible, the automobile industry would rather have the possibility of testing these bus structures in an early state of development. This was the reason why we created a test system for the network management of a CAN-Low-Speed network, which supports the test of an electronic control system in many states of development. This test system is able to check different network structures and to search errors in the ECU's by checking the network management. This is done by an automatic test that generates an evaluation and a report.

In automobile development, wind tunnel measurements are used to optimize fuel consumption and the vehicle's road behavior. The classic measuring technique is based on a stationary vehicle set up in the wind tunnel with stationary wheels. Relative movement between vehicle and road surface is therefore ignored. In more recent studies, measurements have been taken with improved ground simulation. For example, a belt is used instead of the stationary wind tunnel floor and the car wheels rotate. Ground simulation using a belt and rotating wheels generally leads to a reduction in flow angularity at the front wheels, in the same way as blocking the cooling air flow, whereby, as a matter of fact, the aerodynamic drag is reduced. Analogous air flow angle correlations can be established for the effect of underfloor panels.

The present paper reveals the design concept as well as results of experimental investigations, which were conducted in the early design stage of the planned AUDI Aero-Acoustic Wind Tunnel. This low-noise open-jet facility, featuring a nozzle exit area of 11 m2 and a top speed of approximately 60 m/s, enables aerodynamic as well as acoustic testing of both, full-scale and model-scale ground vehicles. Ground simulation is provided by means of a moving-belt rig. The surrounding plenum is designed as a semi-anechoic chamber to simulate acoustic free-field conditions around the vehicle. Fan noise will be attenuated below the noise level of the open jet. The work reported herein, comprises 1/8-scale pilot-tunnel experiments of aerodynamic and acoustic configurations which were carried out at the University of Darmstadt.